High Quality Submerged Sewage Impurity No-Jam Drive Dredge Pump
QW, WQ type non clogging submersible sewage pump is based on the introduction of foreign advanced technology, combined with the use of domestic water pump features a new generation of pumps and the successful development, with significant energy saving effect, anti winding, non blocking, automatic installation and automatic control characteristics. In the carriage of solid particles and long fiber waste convenient, has a unique effect. A unique impeller structure and a new mechanical seal with the pump series, can effectively transfer and long fibers containing solids. Compared with the conventional impeller impeller, the pump impeller uses a single or dual channel form, it is similar to a cross-section of the same size pipe, with the flow of very good. With reasonable volute chamber, the pump impeller has the advantages of high effect, by the static and dynamic balance test, the pump running without vibration. The pump hydraulic performance of advanced, mature, the product has been tested and the performance indicators to meet the standards, Products on the market with its unique function, reliable performance, stable quality, welcomed by the majority of users and praise.
Two, QW, WQ type submersible sewage pump application:
1 municipal engineering construction site;
2 residential sewage discharge;
3 hospital, hotel and other sewage discharge;
4 city sewage treatment plant drainage system;
5 air defense system drainage station, water supply tap water factory;
6 factories, serious commercial sewage pollution emissions.
Three, QW, WQ type submersible sewage pump products:
1 channel anti clogging design of hydraulic components, greatly improve the through capacity of sewage, solid particles can effectively pump diameter 30% through 5 times of fiber material and diameter of pump caliber.
2, reasonable design, reasonable matching motor, high efficiency, energy saving effect is remarkable.
Double path series seal mechanical seal
3 is made of corrosion-resistant tungsten carbide, with a durable, wear-resistant characteristics, can pump the security more than 8000 hours of continuous operation.
4.The pump has the advantages of compact structure, small volume, easy to move, easy installation, no need to build pumping stations, water can sneak into the work, greatly reducing the project cost.
5 pump oil chamber is provided with a water probe, when the mechanical seal on the pump side after the damage of water into the oil chamber, the probe signal, to protect the pump.
6 according to user needs with automatic safety protection control cabinet for the pump Water Leakage, leakage monitoring, overload and over temperature, ensure the pump running safely.
7 double rail automatic coupling installation system, pump installation, maintenance has brought great convenience, but this may not have access to the sump.
8 float switch according to the required water level changes, automatically control the pump to start and stop, without special care.
9 in the context of the use of lift to ensure the motor running overload.
10. According to the motor occasions adopts the water jacket type may be circulating cooling system, can guarantee the safe operation of the pump in the anhydrous state (dry).
11 installation modes: fixed automatic coupling installation and movable free installation two, can meet the needs of different occasions.
Four, QW, WQ type submersible sewage pump type meaning:
S100 pump 100WQ100-15-7.5 discharge mouth nominal diameter (mm) WQ- submersible sewage pump S100 rated current (m no / h) 15 - rated head (m) 7.5 - equipped with motor rated power (kw)
performance parameters :
Number |
Model |
Flow (m*3/h) |
Lift (m) |
Speed (r/min) |
Caliber (mm) |
Power (kw) |
1 |
25-8-22-1.1 |
8 |
22 |
2900 |
25 |
1.1 |
2 |
32-12-15-1.1 |
12 |
15 |
2900 |
32 |
1.1 |
3 |
40-15-15-1.5 |
15 |
15 |
2900 |
40 |
1.5 |
4 |
40-15-30-2.2 |
15 |
30 |
2900 |
40 |
2.2 |
5 |
50-20-7-0.75 |
20 |
7 |
2900 |
50 |
0.75 |
6 |
50-10-10-0.75 |
10 |
10 |
2900 |
50 |
0.75 |
7 |
50-25-10-1.5 |
25 |
10 |
2900 |
50 |
1.5 |
8 |
50-20-15-1.5 |
20 |
15 |
2900 |
50 |
1.5 |
9 |
50-27-15-2.2 |
25 |
20 |
2900 |
50 |
2.2 |
10 |
50-15-25-2.2 |
15 |
25 |
2900 |
50 |
2.2 |
11 |
50-18-30-3 |
15 |
30 |
2900 |
50 |
3 |
12 |
50-24-20-4 |
24 |
20 |
2900 |
50 |
4 |
13 |
50-25-32-5.5 |
25 |
32 |
2900 |
50 |
5.5 |
14 |
50-30-30-7.5 |
30 |
30 |
2900 |
50 |
7.5 |
15 |
50-20-40-7.5 |
20 |
40 |
2900 |
50 |
7.5 |
16 |
65-42-9-2.2 |
42 |
9 |
2900 |
65 |
2.2 |
17 |
65-25-15-2.2 |
25 |
15 |
2900 |
65 |
2.2 |
18 |
65-27-15-3 |
27 |
15 |
2900 |
65 |
3 |
19 |
80-40-7-2.2 |
40 |
7 |
1450 |
80 |
2.2 |
20 |
80-40-15-4 |
40 |
15 |
2900 |
80 |
4 |
21 |
80-50-40-15 |
50 |
40 |
2900 |
80 |
15 |
22 |
100-85-20-7.5 |
85 |
20 |
1450 |
100 |
7.5 |
23 |
100-87-28-15 |
87 |
28 |
1450 |
100 |
15 |
24 |
400-1700-22-160 |
1700 |
22 |
1450 |
100 |
25 |
25 |
500-2800-15-220 |
2800 |
15 |
740 |
500 |
220 |
26 |
700-10000-6-280 |
10000 |
6 |
740 |
700 |
280 |
27 |
100-80-60-37 |
80 |
60 |
1450 |
100 |
37 |
28 |
350-1300-12-75 |
1300 |
12 |
980 |
350 |
75 |
29 |
600-6000-10-280 |
6000 |
10 |
740 |
600 |
280 |
30 |
500-2000-20-160 |
2000 |
20 |
740 |
500 |
160 |
31 |
550-3000-16-200 |
3000 |
16 |
740 |
550 |
200 |
32 |
400-2200-9-110 |
2200 |
9 |
980 |
400 |
110 |
Six, QW, note the use of WQ type submersible sewage pump
1.Pump before use should carefully check the cable is not damaged, the fastener is loose or fall off, pump in the transportation, stored, installed in the process of deformation or damage.
2. with 500V megger electric pump motor and relative insulation resistance, and its value should not be less than 2 ohm, or deal with the stator winding of drying, drying temperature is not allowed to exceed 120 degrees centigrade.
3.There are two kinds of fixed and mobile. This series of pumps are installed. When using fixed automatic installation, should be the chain cable are put respectively from the pump outlet, the connection should be parallel in the pump water outlet) two screw ring or lifting plate on the lifting electric pump. Slowly and evenly along the guide rail decline, until the automatic coupling in place. When mobile type installation is adopted, the first tube set good, chain cable wear two rings under the lifting electric pump, attention can not use the cable as a rope, lest produce risk.
4. The pump is switched on, the direction of rotation from the inlet to see rotate counterclockwise, if electric pump reversal, simply will cable in any second line switch wiring position can be.
5. Electric pump casing wire must be strictly in accordance with the relevant rules are properly connected, in order to ensure use personal safety, in the operation of electric pump, is strictly prohibited in the immediate vicinity of the installation, people in the water work or move, just in case the electric pump leakage and accidents.
6. Electric pump in no special circumstances must be equipped with full automatic water pump control cabinet never directly linked to using grid or knife switch power supply to ensure the normal operation of the electric pump.
7. Shall not be electric pump for a long time in low lift state operation (general use head shall not be less than 60% of the rated head), it is best to control in the proposed use head range within, to prevent electric pump due to overload and burn out the motor.
8 non self circulation cooling device with long running water pump is whole, to prevent the pump overheating damage.
Company Information:
NINGBO ONEREEL MACHINE CO., LTD.
Business Type :Manufacturer.
Product Range :Pumps and other Mechanical and electrical rquipment.
Products Service:Water pumps, Gas pumps, Vertical multistage cemtrifugal pumps,chemical pumps
Year Established :2011.
Certificate :GS , CE , GB , ISO14001 , CCC.
Company Address :No.1229 Baoshan Road, Daqi, Beilun, Ningbo 315800 China, Ningbo, Zhejiang, China.
ONEREEL is specialized in the design and manufacture Steel Spools, Plastic Spools, Cable roller, Yarn Bobbin, aluminum spool , Cable Reel Stand, Sheave Pulley, Cable Conveyor, Hydraulic Puller Tensioner, Gin Poles, Cable Pulling Winch, Safety Tools, Wire Grip, Plastic Parts, and Pump in the industry since 1991. All of our customer spool and wire carrier are engineered and manufactured in our 120,000 square foot state-of-the-art manufacturing plant located in Ningbo, Zhejiang.
ONEREEL is specialized in the manufacture of reels for cables and electric wires, iron axles, disc spool for steel cables and various delivery reels. With strong technological capabilities and full series of production equipment. All of our products go through the dynamic and static balance tests. We have passed the quality system certification ISO9001:2000 to ensure the product quality. Following the standards of GB4004-83, JB/T8997, DIN46395 and DIN46397 in productions.
Hot Product
Our Customer
Packaging & Transportation
Authoritative Certificate
FAQ
Q1: Can I get samples?
A: According to spool model and material, we will advise.
Q2: How long is the sample LEAD TIME?
A: For existing samples, it takes 2-3 days. If no stock, we will advise lead time.
Q3: Can you develop new products?
A: Yes, we have new products developing ability and we are good at developing new mold.
Q4: How much is the freight charge?
A: It depends on spool package volume, if small quantity, volume and urgent goods,
we may advise FEDEX or other couriers' charge for your check.
If volume bigger and by seaway suitable, we provide FOB or CIF price to you.
Q5: What format of the file do you need if I want my own design?
A: We have our own mound workshop and can provide spool or other plastic product developing and injection service.
Q6: How about your service?
A: We have pre-sale service, in-sale service and after-sale service. As "Customer First" is the most important principle of company operation.