220kw Electric High Pressure Deep Well Submersible Pump

• Customization: Available
• After-sales Service: Forever
• Warranty: One Year
• Model NO.: QJ-300
• Max.Head: 10-30m
• Max.Capacity: 50-100 L/min
• Driving Type: Motor
• Material: Stainless Steel
• Structure: Single-stage Pump
• Assembly: No
• Power: Electric
• Start Up: Electric Pump
• Type: Deep Well Water Pump
• Application: Submersible Pump
• Industry: Mechanical Pump
• Media: Sea Water Pump
• Performance: No
• Theory: No
• Power Source: Electric
• Flow: 15m3/H-1000m3/H
• Head: 10m-600m
• Motor Power: 2.2kw-420kw
• Frequency: 50Hz, 60Hz
• Transport Package: Wooden Package
• Specification: Steel
• Trademark: ONEREEL
• Origin: Ningbo China
• Production Capacity: 1000 Pieces a Month
• Package Size: 60.00cm * 60.00cm * 50.00cm
• Package Gross Weight: 150.000kg

Product Description

220kw Electric High Pressure Deep Well Submersible Pump

 

Product Description

 

 

A, QJ series submersible pump units will be divided into four most:
1, YQS well with filling water diving three-phase asynchronous motor (matching leads to cable)
2, water pump assembly (general factory with motor assembly together)
3, Yang pipe (steel and rubber hose can supply according to the requirements of customers)
Form a complete set of 4, starting control box (usually the factory)

Second, the QJ series deep well submersible pump features:
1, the QJ series supporting for YQS series submersible pump Wells with water filling type diving three-phase asynchronous motor, the stator winding is adopted in the water is not subject to corrosion of polyethylene insulation waterproof electromagnetic wire, nylon sheathed winding directly soaked in water. 
2 upper and lower guide bearing, thrust bearing and the pump and motor bearing adopts special material and water lubrication structure, has good corrosion resistance. 
3, to prevent mud into the motor chamber, upper motor equipped with positive and negative two skeleton oil seal and dumped hydrosphere, formed a labyrinth sand control device. 
4, the lower part of motor is equipped with rubber membrane, voltage regulator when the motor stop or load changes caused pressure changes in the body, can be made of rubber membrane voltage regulator automatically regulate the internal pressure. 
5, water pump USES centrifugal impeller, single-stage high lift and compact structure.
The unit installation

A, the well preparation:
1, installed a tripod, hanging reed or hoist. Hoisting should not be less than 2 tons. 
2, ready to wrench, hammer, screw knife, electrical tools and using the instrument. 
3, check whether the submersible electric pump assembly is good, accessories are complete.To unload the water filter section, with pick silk knife from the impeller mouth the ball at the top of the water festival in leaf version, pulled the turn, pump impeller rotation.If still cannot turn, pulled the impeller can remove base, with wood mat to the motor shaft end, with a hammer knock, pump shaft to rotate. 
4, unscrewing the top two motor hole bolts, at the same time, the water bottom bolt fastening motor, the motor internal cavity filled with clean water, pouring hole bolt and screw. 
5, with 500 v megohmmeter shake test motor windings of (the cabinet) insulation resistance shall be not less than 150 ohms. 
6, bandaging cable connector: the three core or single core cable size respectively according to the requirements of the appended drawings joint strip of rubber layer and the many strands of copper core line clean the rust layer, and then respectively the three cable core with splicing method relatively splicing and firm, the splicing length shall be not less than 50 mm.Best of large capacity motor with a bare wire tightly wound after a layer, then use soldering welding processing, ensure joint is good and reliable work.After cable joint connected, with sticky rubber belt from the first three core half fold dress 1-2 layer, then use plastic adhesive tape halved bandage 3-4 layer, specific operation can see figure "" cable joint process. 
7, cable joint, will lead to cable (including cable joint) all immersed in the water, with a 500 v megohmmeter again to ground insulation resistance measurement of motor winding and lead to cable, not less than 150 ohms can well. 

Second, the matters needing attention in the process of installation:
1, in the process of the pump in the well, if found to have stuck phenomenon, to rotate and flip young conduit in time, in order to overcome dead point, submersible electric pump to avoid stuck or damage to the cable. 
2, install piping to short pimps MATS, uniform and tighten the bolt. 
3, in the process of the pump in the well, the cable should be close to in each section Yang water pipes, plastic belt or nylon rope etc. Water resistant rope fastened, fight snap or crowded broken cable. 
4, install and lifting submersible pumps, is absolutely not allowed to use as the rope sling cables. 
5, according to the well flow sand silting situation, determine the submersible electric pump the minimum distance from the bottom.Avoid the submersible electric pump embedded in mud, general requirements from submersible pump into the bottom of not less than 3 m, dynamic water letter from the inlet section of not less than 1 meter, and under the pump into the depth should comply with the regulations of the selected type pump head. 
Unit
6, submersible pumps must be installed upright, can not lay down.Specific installation requirements shall be see "submersible pumps installation plan". 
 

 

Product Parameters

 

Technical Parameter

Product Specification		Packing & Shipping
MODEL	250 QJ 80-40/2	MOQ	50pcs
Voltage	220V	Brand	ONEREEL(support OEM)
Power	750W	Certificate	CE, ISO
Frequency	50HZ	Packing	Corrugated Cardboard Carton + Foam  Fully guarantee the safety of transportation
Max. Flow .	2m³/h	Warranty	12 months
Max. Head	100m	Place of Origin	Zhejiang, China
Inlet/Outlet	1inch	Delivery term	30-40 days
Cable	18m	Loading port	Ningbo or other china port
Max. depth	5m	LXWXH	66.5*12*18.5mm
Weight	13.5kg	20ft.Qty.	1800pieces

 

ONEREEL is specialized in the design and manufacture , , , ,   , ,  , , , , , , , , and in the industry since 1991. All of our customer spool and wire carrier are engineered and manufactured in our 120,000 square foot state-of-the-art manufacturing plant located in Ningbo, Zhejiang.

ONEREEL is specialized in the manufacture of reels for cables and electric wires, iron axles, disc spool for steel cables and various delivery reels. With strong technological capabilities and full series of production equipment. All of our products go through the dynamic and static balance tests. We have passed the quality system certification ISO9001:2000 to ensure the product quality. Following the standards of GB4004-83, JB/T8997, DIN46395 and DIN46397 in productions. 

 

 

Hot Product

Our Customer

 

 

Packaging & Shipping

 

Packaging & Transportation

 

Certifications

 

Authoritative Certificate

 

FAQ

 

FAQ

Q1: Can I get samples?
A: According to spool model and material, we will advise.
Q2: How long is the sample LEAD TIME? 
A: For existing samples, it takes 2-3 days. If no stock, we will advise lead time.
Q3: Can you develop new products?
A: Yes, we have new products developing ability and we are good at developing new mold.
Q4: How much is the freight charge?
A: It depends on spool package volume, if small quantity, volume and urgent goods, 
we may advise FEDEX or other couriers' charge for your check. 
If volume bigger and by seaway suitable, we provide FOB or CIF price to you.
Q5: What format of the file do you need if I want my own design?
A: We have our own mound workshop and can provide spool or other plastic product developing and injection service.
Q6: How about your service?
A: We have pre-sale service, in-sale service and after-sale service. As "Customer First" is the most important principle of company operation.